Difference between revisions of "Powerupgrade"
(→Groups) |
|||
| Line 17: | Line 17: | ||
=Groups= | =Groups= | ||
| − | The following groups | + | The following groups have been made in the new fusebox: |
| + | * hardware ('dirty') room | ||
| + | * kitchen fixed equipment (dishwasher + waterheater) | ||
| + | * kitchen fixed equipment (microwaves, fridges, cofvevemaker) | ||
| + | * 2 x kitchen open sockets (water cooker, covfefemaker, electric pans, toasters) | ||
| + | * cooking group (3 phase) for builtin induction cooking stove | ||
| + | * 3-phase 16A socket hardware room | ||
| + | |||
| + | The following still need install/connection: | ||
| + | * 2 x serverroom (redundancy) | ||
* makerlane | * makerlane | ||
* radiolane | * radiolane | ||
| Line 25: | Line 34: | ||
* main powerbar | * main powerbar | ||
* aux powerbar | * aux powerbar | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
This adds up to: | This adds up to: | ||
| − | * | + | * 13 simple 16A groups |
| − | * | + | * 2 3-phase 16A groups |
Revision as of 12:52, 23 January 2019
Intro
Electrical power at techinc was done with very limited resources and funds (practically zer0) that we had at the time. Now we're reaching the point where those limitations are becoming increasingly evident. A number of people have expressed their desire for a substantially larger feed than the 3 x 13A/16A we have now. As such the Powergroup has undertaken the planning to upgrade the power supply and distribution to the space.
What?
Install a 5x 6mm² cable between the UR power cabinet down stairs to the Fusebox in the dirty room, then distribute this to various circuits round the space, replacing the separate UR provided power circuits such as the one in Maker lane, most of the power in Main space, and the network rack.
How?
A 5x6mm2 cable was pulled along the existing lower capacity cable. Nn electrician has connected the cable, while upgrading the 3 16A fuses downstairs. The fuses downstairs were upgraded to 3 x 35A slow. The new fusebox is a ABB Mistral IP65 3 x 18 box. It has a main switch (4 wire simple switch 40A), fuse 1P(+N not connected) on each phase (40A B=fast profile) after which the various phases and groups are split out. There is an earth protection (aardlekschakelaar) on phases L1 and L2 with 4 groups; two on L3, giving a total of 14 single groups. There are also 2 3-phase groups with builtin earth protection ('alamat') for cooking, and for the dirtyroom 3-phase socket.
There is also a 3-phase power meter with LCD display installed (suitable up to 3 x 80A). It has a pulse interface for measuring power usage (1 pulse per watt). See https://www.eltako.com/fileadmin/downloads/de/datenblatt/Datenblatt_DSZ15D-3x80A.pdf and https://www.eltako.com/fileadmin/downloads/de/_bedienung/DSZ15D-3x80A_28380015-1_dt.pdf
The last group is used for a WCD in the case (normally not used, only for maintenance purposes), and powering a 5V 2A DIN PSU which powers a raspbery Pi Zero-WH. The intention is to run something like http://ondrej1024.github.io/emond/ on it to measure power usage, both on local display and on some part of the space state API and/or MQTT.
Groups
The following groups have been made in the new fusebox:
- hardware ('dirty') room
- kitchen fixed equipment (dishwasher + waterheater)
- kitchen fixed equipment (microwaves, fridges, cofvevemaker)
- 2 x kitchen open sockets (water cooker, covfefemaker, electric pans, toasters)
- cooking group (3 phase) for builtin induction cooking stove
- 3-phase 16A socket hardware room
The following still need install/connection:
- 2 x serverroom (redundancy)
- makerlane
- radiolane
- main hacktable + fireplace
- solderlane
- main powerbar
- aux powerbar
This adds up to:
- 13 simple 16A groups
- 2 3-phase 16A groups
