2020 Stay The F*** home Techinc Solder Kit

Projects
Participants
Skills	PCB Design, Soldering
Status	Active
Niche	Electronics
Purpose	World domination

2020 Stay The F*** Home Techinc Solder Kit

Following Hack42 and Revspace, Techinc now also has its own 25mm radius round object! Since many of you may suffer from flux-resin withdrawal due to the space being closed, and because the space could do with some extra cash, said round object will be for sale as an SMD solder kit! The kit will include a PCB, a pre-programmed microcontroller, a battery holder, LEDs to taste, a bit of solder (, if requested) and some passives.

I Brainsmoke, have reimbursed myself for the material costs, the rest of the money will go to the association.

• 

  Top side

• 

  Bottom side

• 

  PCB in action

What does it do?

• Show an animation
• Show a custom animation sent via 9600 baud UART [8 bytes of brightness values]

The badge can be powered either using a cr2032 battery, or externally, up to 5V.

What does it cost?

	product cost
Techinc 2020 PCB (bare PCB only)	EUR 7
Techinc 2020 PCB Solder Kit	EUR 10
Techinc 2020 PCB already-soldered	EUR 40

Kits are available at techinc.

Solder instructions

MCU Code

https://github.com/brainsmoke/charliepdk

Driving the LEDs externally using an Arduino

example program

#include <SoftwareSerial.h>

SoftwareSerial s(2, 3);

void setup()
{
    s.begin(9600);
}

uint8_t gamma[256] = {
// gamma = ['{:3d},'.format(int(255*x**2.6 // (255**2.6))) for x in range(256)]
// for i in range(0,256,16):
//     print (''.join(gamma[i:i+16]))

   0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,
   0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  1,
   1,  1,  1,  1,  1,  1,  1,  1,  2,  2,  2,  2,  2,  2,  2,  3,
   3,  3,  3,  3,  4,  4,  4,  4,  4,  5,  5,  5,  5,  6,  6,  6,
   7,  7,  7,  7,  8,  8,  8,  9,  9,  9, 10, 10, 10, 11, 11, 12,
  12, 12, 13, 13, 14, 14, 15, 15, 16, 16, 17, 17, 18, 18, 19, 19,
  20, 20, 21, 21, 22, 22, 23, 24, 24, 25, 26, 26, 27, 27, 28, 29,
  30, 30, 31, 32, 32, 33, 34, 35, 35, 36, 37, 38, 39, 39, 40, 41,
  42, 43, 44, 45, 46, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56,
  57, 58, 59, 60, 61, 63, 64, 65, 66, 67, 68, 69, 71, 72, 73, 74,
  75, 77, 78, 79, 80, 82, 83, 84, 86, 87, 88, 90, 91, 92, 94, 95,
  97, 98,100,101,103,104,106,107,109,110,112,113,115,117,118,120,
 121,123,125,126,128,130,132,133,135,137,139,140,142,144,146,148,
 150,152,153,155,157,159,161,163,165,167,169,171,173,175,177,179,
 182,184,186,188,190,192,194,197,199,201,203,206,208,210,213,215,
 217,220,222,224,227,229,232,234,237,239,242,244,247,249,252,255,
};

void loop()
{
    uint8_t i;
    int k;
    for (;;)
    {
        for (k=0; k<255; k+=32)
            s.write( gamma[(k-i)&0xff] );
        delay(10);
        i+=11;
    }
}

FAQ

* What MCU is used?
  the used MCUs are a Padauk PFS154, or a Padauk PMS150C (depending on availability)
  but the design is also pin-compatible with the Attiny2x2 series as well as (some?) SOP8 PIC micros
* Can the MCU be programmed in-circuit?
  Sadly no, but you can display custom animations using a UART rx pin