SuckWell

From Technologia Incognita
Revision as of 03:15, 17 December 2015 by Ultratux (talk | contribs)
Jump to: navigation, search
Projects
SuckWellproto1.jpg
Participants Ultratux
Skills Soldering, pneumatics, mechanics
Status Active
Niche Mechanics
Purpose Fun

SuckWell...er...

Two decades ago I purchased a Weller® desoldering contraption that is compatible with the venerable WTCP-S soldering stations. It consists of a heated suction tip leading to a rubber 'bellow' that you're meant to squeeze & hold and release it at the right moment when the solder you want to suck away is liquefied. For various reasons I never had any success using it. Probably partly because the suction it creates is much too small and acts too slowly, especially compared to your standard desoldering tools which are spring-loaded. And in other part possibly because the act of suddenly releasing the bellow is not entirely compatible with keeping the desoldering tip steady and motionless at exactly the right spot. So it ended up in a box in the attic.


Now with the Chinese offering various nice and cheap parts I decided it was worth a shot to electrify it; a small vacuum pump, a solenoid valve, some buffer vessel and some tubing ought to be all that's required. The hacked soldering station I built has plenty of extra power available, both 12V and 24V (100W ring transformer). It just needs a rectifier for the vacuum pump and valve.


Having finally received the pump and valve this weekend I set out to acquire fitting tubing and make a quick 'n dirty prototype setup, as pictured.


Testing it, this vessel (a small soda bottle) builds up sufficient vacuum to have the tip suck air for over 5 seconds so that ought to be largely enough. But maybe the nozzle is simply too small. I think I have different sizes nozzles in that box in the attic, so I ought to try real-life desoldering to get proper test results. Was not successful yet in locating my spare nozzles.


I've decided what to go for on the iron; a tiny glass bottle (think perfume/medicine size) with two metal conduits entering from front side. That ascertains hot solder can never get sucked in to the tube (unless it learns to do a mid-flight U-turn) and thermally insulates the PVC tube enough from the hot tip. I used a piece of aluminium 6mm OD pipe that I managed to fold as a U-turn using a pulley wheel as 'bed' to help avoid it kinking or breaking. (You gotta get a little inventive when your pipe bender is only suited for 12mm and 15mm...) Lacking a suitable cork I figured to glue both pipe ends into the bottle using two-component adhesive. It will likely be years, if not decades, before the bottle fills up with solder, so it's a design compromise I dared to make. I have to wait some 24 hours for the glue to cure completely now before I can test whether my design holds up to scrutiny... one aspect is physical strength... the whole assembly is not supposed to be attached to the iron except by the heating element. That way you can still replace this thing with a regular solder tip. But that then means that the glass bottle neck combined with the glue has to withhold all the stresses that the movement and weight of the tube exert on it... that's interesting. As it turns out, it's mighty solid.


Today I tried to purchase tiny '2-oor slangklemmen' in vain. These will be added later. However, the rest of the work got finished today; I thought long and hard about a suitable case but found none that were good. I decided I wanted to overhaul my solder station anyway so I rethought all of it and made a new layout, housing some extra electronic parts inside the old case, but leaving all of the pneumatics just outside, in plain sight. I added a bridge rectifier, an extra switch for the pneumatic section. A microswitch to activate the valve has been wired up but still needs to find a nice spot on the soldering iron. That's the second todo item.


The end results are depicted here.

Entire unit with 3 weller irons (only two should be used simultaneously; 100 W transformer):

IMG 20151216 235233.jpg


Soldering iron closeup. Missing is the actuator switch. Ideally I'd want it on the tube assembly, not on the iron, as the iron then can simply be detached from it and fitted with a regular tip for normal work. Then again, the switch also needs to be in a spot where it is easy to operate. Finding a solution to both is hard. For instance, the switch would be okay on the underside of the bottle but... then it would impede the soldering iron from being detached too; it would block it. So I'm not yet clear on how to best do that...

IMG 20151216 235247.jpg


First tests de-soldering stuff were moderately successful. The suction is good, but I need to try this on more 'demanding' PCBs too, like double-sided, multilayer, and, the horror! lead-free solder material. A mild worry is that none of the sucked-up solder has yet ended up in that bottle, so it will likely start to clog up the metal pipe between tip and bottle. I need to test that hypothesis and also find out how well or hard that is to free up. I'll try to use a bendable guitar or bass string I guess, to push stuff out. More testing soon.


Parts list (so far):

small 12V vacuum pump, aliexpress, $ 8.85
solenoid air valve, aliexpress, $ 4.97
Weller desoldering thing, $ unknown (*)
Various tubing, found in attic and elsewhere
bridge rectifier
microswitch to mount on soldering iron
desolder section on/off switch 
wiring
aluminium tube 6mm OD
small old bottle from medicine cabinet or similar
...
possibly an arduino and a pressure sensor to tell the pump when it should engage

(*) Not exactly advocating to purchase it, but Reichelt still sells it [[1]]