Difference between revisions of "DeltaFlightcase"
m |
m |
||
| Line 7: | Line 7: | ||
Building a proper flightcase for a Cerberus-derived delta 3D printer. It ought to be flexible enough to house both the newer -printed- model and the original model in ways that even rough treatment will likely be survived gloriously. | Building a proper flightcase for a Cerberus-derived delta 3D printer. It ought to be flexible enough to house both the newer -printed- model and the original model in ways that even rough treatment will likely be survived gloriously. | ||
| − | Challenges: | + | ===Challenges:=== |
* <s>Find ways to keep weight limited so it can still be carried by a single person.</s> | * <s>Find ways to keep weight limited so it can still be carried by a single person.</s> | ||
* Determine how to best design inside of case to accommodate the different variations of the cerberus. | * Determine how to best design inside of case to accommodate the different variations of the cerberus. | ||
| Line 15: | Line 15: | ||
Due date: no later than December 19th, 2014 | Due date: no later than December 19th, 2014 | ||
| − | Challenges met: | + | ===Challenges met:=== |
| − | |||
* Cheap non-birch 9 mm plywood; good compromise between price, sturdyness and weight. | * Cheap non-birch 9 mm plywood; good compromise between price, sturdyness and weight. | ||
* Found wheels and butterfly-lock-thingies in my attic. | * Found wheels and butterfly-lock-thingies in my attic. | ||
| Line 22: | Line 21: | ||
* Protection will basically be just a tight fit inside between 20mm hard foam plates | * Protection will basically be just a tight fit inside between 20mm hard foam plates | ||
| − | Progress: | + | ===Progress:=== |
* All materials ordered and received, just need to move foam plates to TI by bike. | * All materials ordered and received, just need to move foam plates to TI by bike. | ||
* Bottom half of case made, glued. Next up is painting. Only after painting can wheels etc be mounted. | * Bottom half of case made, glued. Next up is painting. Only after painting can wheels etc be mounted. | ||
* Top half is under way. It bends a bit too much, so it may need slight redoing or adjustment. | * Top half is under way. It bends a bit too much, so it may need slight redoing or adjustment. | ||
* Bought/ordered a pneumatic rivet gun; mounting 80x 5mm rivets with the cheapest possible Gamma manual rivet gun is quite hard and painful work... | * Bought/ordered a pneumatic rivet gun; mounting 80x 5mm rivets with the cheapest possible Gamma manual rivet gun is quite hard and painful work... | ||
Revision as of 05:07, 13 December 2014
| Projects | |
|---|---|
| Participants | Ultratux |
| Skills | Woodworking, measurements, painting |
| Status | Active |
| Niche | Mechanics |
| Purpose | Use in other project |
Building a proper flightcase for a Cerberus-derived delta 3D printer. It ought to be flexible enough to house both the newer -printed- model and the original model in ways that even rough treatment will likely be survived gloriously.
Challenges:
-
Find ways to keep weight limited so it can still be carried by a single person. - Determine how to best design inside of case to accommodate the different variations of the cerberus.
- Find some way to cut foam into arbitrary shapes
-
Find affordable sources for support foam and 'hang en sluitwerk' plus wheels.
Due date: no later than December 19th, 2014
Challenges met:
- Cheap non-birch 9 mm plywood; good compromise between price, sturdyness and weight.
- Found wheels and butterfly-lock-thingies in my attic.
- Ordered pre-cut 'hard foam' at some shop, so possibly avoided cutting it myself.
- Protection will basically be just a tight fit inside between 20mm hard foam plates
Progress:
- All materials ordered and received, just need to move foam plates to TI by bike.
- Bottom half of case made, glued. Next up is painting. Only after painting can wheels etc be mounted.
- Top half is under way. It bends a bit too much, so it may need slight redoing or adjustment.
- Bought/ordered a pneumatic rivet gun; mounting 80x 5mm rivets with the cheapest possible Gamma manual rivet gun is quite hard and painful work...
