Difference between revisions of "AnusCopter"
| Line 12: | Line 12: | ||
* 2013-11-26 charged batteries, added receiver and battery strap | * 2013-11-26 charged batteries, added receiver and battery strap | ||
* 2013-11-27 battery monitor leads (and header for LEDs) added | * 2013-11-27 battery monitor leads (and header for LEDs) added | ||
| − | + | * 2013-12-04 XT60 to power board soldered | |
| + | * 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS | ||
==In transit== | ==In transit== | ||
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC | 4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC | ||
| Line 18: | Line 19: | ||
FS-TH9X-B-Module | FS-TH9X-B-Module | ||
| − | + | Some 8045 CW CCW Propellers | |
10x Male+Female XT60 connector | 10x Male+Female XT60 connector | ||
25x M3 7mm Philips head screw | 25x M3 7mm Philips head screw | ||
| − | |||
| − | |||
XBee Explorer Dongle + Quad-band Cellular Antenna SMA + SMA connector for XRF | XBee Explorer Dongle + Quad-band Cellular Antenna SMA + SMA connector for XRF | ||
| Line 40: | Line 39: | ||
4x Turnigy D2822/17 1100KV Brushless | 4x Turnigy D2822/17 1100KV Brushless | ||
| + | |||
| + | 4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC | ||
| + | |||
| + | 4x 8045 CW CCW Propellers | ||
AeroQuad 32 Flight Control board v2 | AeroQuad 32 Flight Control board v2 | ||
| Line 48: | Line 51: | ||
2x XRF wireless RF radio UART RS232 | 2x XRF wireless RF radio UART RS232 | ||
| + | |||
| + | LS20031 GPS | ||
10 strand dupont cable female-female | 10 strand dupont cable female-female | ||
Velcro tape <3 | Velcro tape <3 | ||
| + | |||
| + | XT60 and 3.5mm gold bullet connectors | ||
==Accessoires== | ==Accessoires== | ||
Revision as of 20:33, 7 December 2013
| Projects | |
|---|---|
| |
| Participants | Ranzbak, The JinX |
| Skills | Soldering, Electronics, Coding, UI design |
| Status | Getting parts |
| Niche | Electronics |
| Purpose | Fun |
Build log
- 2013-11-20 put AeroQuad in case
- 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm)
- 2013-11-26 charged batteries, added receiver and battery strap
- 2013-11-27 battery monitor leads (and header for LEDs) added
- 2013-12-04 XT60 to power board soldered
- 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS
In transit
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC
FS-TH9X-B-Module
Some 8045 CW CCW Propellers
10x Male+Female XT60 connector
25x M3 7mm Philips head screw
XBee Explorer Dongle + Quad-band Cellular Antenna SMA + SMA connector for XRF
T B A
Landing gear
Ultrasonic Range Finder (LV EZ-0)
Camera's and FPV transmitter / receiver
Components
HJ 450 "classic" frame
4x Turnigy D2822/17 1100KV Brushless
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC
4x 8045 CW CCW Propellers
AeroQuad 32 Flight Control board v2
Turnigy 9X 2.4GHz 8Ch Receiver (V2)
2x Turnigy 2200mAh 3S (30C+35C) LIPO
2x XRF wireless RF radio UART RS232
LS20031 GPS
10 strand dupont cable female-female
Velcro tape <3
XT60 and 3.5mm gold bullet connectors
Accessoires
Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO
Turnigy Accucel-6 50W 6A Balancer/Charger
ToDo
Installing ESCs
Power wiring
Serial uplink (telemetry)
