AnusCopter

Projects
Participants	Ranzbak, The JinX
Skills	Soldering, Electronics, Coding, UI design
Status	Active
Niche	Electronics
Purpose	Fun

Specs

Weight: 1111g

Power: 2200mAh - 8000mAh 11.1V

Max power: 410W

Components

Rear end

HJ 450 "classic" frame mixd with Firefly

Extended legs http://www.thingiverse.com/thing:135063

4x Turnigy D2822/17 1100KV Brushless

4x 8045 CW CCW Propellers

4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC (2 with BEC)

AeroQuad 32 Flight Control board v2 (baloo)

Turnigy 9X 2.4GHz 8Ch Receiver (V2)

Turnigy 2200mAh 3S (30C+35C) LIPO

XRF wireless RF radio UART RS232

LS20031 GPS + micro JST 6 (4 wires used)

Sony 600TVL CCD Camera

MAX7456 OSD Breakout http://www.hobbytronics.co.uk/max7456-osd-breakout

Elgae TS 351 5.8Ghz 200mW Wireless AV Transmitter

10 strand Dupont cable female-female

6 female jumper leads

4x 470 Ohm resistor and 2 white 5mm LED 2 red LED 5mm

1x XT60 and 8x 3.5mm gold bullet connectors

Heat shrink tubes

Velcro tape <3

Accessoires

Slightly modded Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO + FS-TH9X-B-Module

Elgae RC 305 5.8Ghz AV Receiver

XBee Explorer Dongle + XRF wireless RF radio UART RS232 + SMA connector + Quad-band Cellular Antenna SMA

• Case for XRF dongle http://www.thingiverse.com/thing:204516

Turnigy Accucel-6 50W 6A Balancer/Charger

LIPO charge bag

Spare parts

3x Turnigy D2822/17 1100KV Brushless

10x XT60 gold male and female connectors

Firefly fibreglass body parts

Some 8045 propellers

Odds, ends and broken motors

In transit

10x Micro JST 1.25 7-Pin Connector with Wire

8" TFT LCD 800x600

25x M3 7mm Philips head screw

2 black 2 white HJ frame arms

Dupont wire female female

Velcro straps

Some 8045 and 9050 propellors

ZIPPY Flightmax 8000mAh 3S1P 30C Lipo

ZIPPY Compact 5000mAh 3S 25C Lipo

12V 10A Switching PSU

Build log

First crash

• 2013-11-20 put AeroQuad in case and played around with it a bit Mac and Linux version of AeroQuad Configurator lack a bit
• 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm) will need some more of those
• 2013-11-26 charged batteries, added battery strap and receiver and wired it up with 10 wire Dupont cable
• 2013-11-27 battery monitor leads (and header for LEDs) added drilled/routed a hole in top of case for jumper leads
• 2013-12-04 XT60 wired and soldered to power distribution board
• 2013-12-07 soldered and wired 8x 3.5mm gold bullet connectors, installed ESCs, soldered 6 pin micro JST to GPS
• 2013-12-11 added 4 pin micro JST to XRF module and added 2 front and 2 rear LEDs
• 2013-12-15 inserted TX installed props for first time, created case for XRF
• 2013-12-21 new rear end frame upgraded fixation of LEDs
• 2013-12-22 more zip-ties and some housing tests
• 2013-12-26 replaced some motors, started 3D printing first leg
• 2013-12-27 printing 2 more legs, bought 20mm M4s RVS nuts and bolts have to saw/dremel a bit off added battery wire containment strap
• 2013-12-28 switched blue LED with a green one + 22K Ohm resistor in RX. finished quad legs, changed two arms and printed a non-fitting FPV thing
• 2013-12-29 replaced another arm, those Firefly ones are flimsy this one broke after I killed throttle to not fly into myself at max 70 cm up
• 2014-01-06 tested FPV cam, TX and RX need to wait for micro JST7 connector for OSD looked at http://www.thingiverse.com/thing:139423 for protection
• 2014-01-08 printed cam mount http://www.thingiverse.com/thing:139423

Flight log

• 2013-12-15 maiden flight .. second flight went too high, crashed from 6m and broke frame
• 2013-12-22 small flight test in the dark, too windy to check at altitude but all controls seem to work fine :)
• 2013-12-26 major imbalance on first two test flights, second and third night flight went mostly great though . .
• 2013-12-27 indoor flight tests worked like a charm very stable .. battery empty indication problematic
• 2013-12-28 crash on first attempt, stable flight indoor still .. might have to reconfig on ground instead of in space
• 2013-12-29 emptied one battery indoor by doing a simple parcour .. broke another Firefly arm after falling ~60 cm on carpet :/
• 2014-01-04 indoor testing, want to do a power benchmark soon, getting better feel for flying on 100% and non exponential

T B A

Outer shell to make it more crashworthy (probably not necessary)

Ultrasonic Range Finder (LV EZ-0)

Bigger, better and at-least less fragile in the arms department

Brushless Gimbal thing and Camera

GSM/4G stuff for long range?

Links

Some more useful reading

Other local flying projects

Justa copter 1

Phicoh Copter 1

NarCopter

Yiodah copter

DiscoDrone

QuadcopterAmraam

Social

Quadcopter workshop

Useful

STM32 flightcontroll

Aero Quad

Lessons learned

Check all your screws between all flights

• lost 4 on maiden flight and 2 later on
• possibly lost a prop that way (first crash)

Flame Wheel clones have pretty fragile arms don't buy the Firefly ones!

Overcompensation is a bitch

Being in a zen state helps

I can do this

Flying is fun

If you wanna go FPV get monitor without 'blue screen'

Is on Fire?	Not Yet