Lulzbot TAZ 3D Printer

TechInc Inventory
Description	XYZ gantry-based 3D printer; single extruder
Make	Lulzbot
Model	TAZ
Manufacturer Link	http://www.lulzbot.com/?q=products/taz-3d-printer
Category	Other
Operational Status	Working
Super Users	Justa, Nathan7, Ultratux, Amx109
Received at	2013/10/28
Acquisition Details	Donated by Aeva; Lulzbot representative
Owner	Techinc

Overview

The Lulzbot TAZ printer is a commercial 3D printer put together and sold by the people at Lulzbot.

It is designed using a metal-based frame with custom 3d-printed parts for corner-couplings and extruder-sections as well as controller-casing.

We had one donated to us by Lulzbot on the 28th of October through Aeva, a Lulzbot representative who was looking for a good home for one that was used as a demonstration-unit at (at least) the BlenderConference the weekend before.

Techninc ended up being the lucky recipient of the unit and Aeva and Chris came by to help set up and test the unit, as well as provide assistance and technical guidance on using the machine.

Specifics

The machine is based on a regular XYZ-oriented setup; much like the Prusa i3. A pair of motors actuate the Z-height spindles, guiding the X-arm up along a set of guiding-rails. The Y-movement is realized by moving the heated printing-bed across a set of guiding-rails.

The X-arm has an extruder-unit referred to as the 'Budaschnozzle 2.0' with a 0.35mm nozzle fitted.

ABS PRINTING READY

The bed and extruder are, as delivered, suitable for ABS-printing only. The bed is coated with a special plastic; the extruder lacks a fan.

PLA PRINTING: NEEDED

For printing with PLA, one would need to fit a fan-unit on the side of the extruder-head (please find the two suppled screw-holes there) that would blow air across the cool-ribs and the printed object but would *NOT* blow across the metal of the nozzle.

Also, the bed-surface should be adjusted , as well as heater-temp and extruder-temperature settings.

As of 2013-11-17, the Lulzbot has been modified to be able to use PLA as stock-material as well. It has been fitted with a fan-duct mounted on the side by two M3 hex-key bolts. The supplied 40x40mm fan seems a bit low-powered and should perhaps be replaced with a stronger version in the future.

Wiring has been made to run through the proper cable conduit and has been made so that the fan can be easily replaced by means of a male/female connector on the top of the extruder-carriage.

Technical specifications

• Controller: Rambo v1.1
• Print area: 298mm x 275mm x 250mm
• Print volume: 20,500cm3
• Top Print Speed: 200mm/sec (7.9in/sec)
• Print Tolerance: 0.1mm (0.0039in) in X and Y axes. Z axis is dependent on layer thickness
• Layer Thickness: 0.075mm to 0.35mm (0.003in - 0.0138in)
• Supported Materials: ABS, PLA, HIPS, PVA, and wood filaments
• Usable Filament Sizes: standard 3mm (0.1in)
• Temperature: Maximum operating temperature (Extruder), 240C (464F)
• Temperature: Maximum operating temperature (Heated Bed), 120C (248F)

• Overall Dimensions: 680mm x 520mm x 515mm (26.8in x 20.5in x 20.3in)
• Weight: 11kg (24.25lbs)

Printing

Preparing a design for printing

• Info about STL, requirements , Slic3r and filament *

Preparing the printer for printing

When you've finished using Slic3r and have prepared a G-code file for use with the printer; please make sure that the G-code was for the right model printer, as well as the right type of filament loaded in the printer.

Currently, the actual printing process is performed and monitored by PronterFace. Please find it in the '3d printing tools' tab at the top of the desktop. A future arrangement might instead use OctoPrint. Procedures for either should be greatly the same.

=== Connecting to the printer

• Make sure that the printer is on and connected (both PSU-brick and control-unit). Also to USB.
• Start the printing-software (PronterFace)
• The printer will be either on /dev/ttyACM0 or /dev/ttyACM1
• When pressing 'connect', the Lulzbot will report it's identity if the right port is selected in the side-bar on the right.

If you can move the head around with the interface provided on the left, you are connected to the right printer.

Pre-print routine

• Set the 'bed' and 'extruder' temperatures according to the material you are going to print with and use the 'SET' buttons on the right of the selections to turn the heaters on. This will pre-warm the printer for use.
  • If you change your mind and decide to NOT print , DO NOT FORGET TO TURN HEATERS OFF

While waiting for the temperature to get to the right levels, you now have time to clean up and prepare the bed for printing in case the previous user of the printer left the bed un-ready for a next print-job:

• Turn motors off (click 'Motors off' in interface; this will take the power off. Do not try and force bed to move with motors engaged)
• Remove any left-over material from a last print-job. Dispose of plastic-scrap properly. Put 'ABS' and 'PLA' into the proper containers provided.
• Use ABS-glue or another adherent to re-coat the bed homogeneously.
  • Find the white lidded jar with ABS-glue
  • Use a kitchen-towel folded into a swab and dip it into the glue to create a brush
  • Quickly but evenly coat the uncoated parts of the bed with this mixture.
  • Put the lid back on the jar!
  • Dispose of swab properly (do not leave on ANY surface) or store properly for next use.

Next up is checking if the extruder functions properly enough and/or if the filament is fed correctly through the gearing for it.

• Use the Z-height control in the printing-interface to move the extruder head upwards; 2 or 3 CM will do.
• When the temperature is high enough, use the 'Extrude' button to extrude an amount of plastic.
  • The Lulzbot is protected against trying to extrude when the temperature is not high enough (a so called 'cold extrusion'). The Prusa seems to NOT prevent you from trying this. This will damage the filament and perhaps (and much worse) the gear-system. Be careful with this!
• Remove extruded material with a set of long pliers or a scraping-tool and dispose of appropriately.

If the bed's coated to your liking and the extruder works; you're ready for printing. One last step, homing the extruder.

Press the little 'house' to home the extruder in all axis. In Pronterface, this is on the lower-left corner of the 'circle' interface. You can home individual axis by using the 'X-home', 'Y-home' or 'Z-home' icons.

When homing, it can be helpful to take note of the Z-movement downwards. The head will likely touch the bed at first, then retract and then approach the bed more slowly. Ultimately it should NOT push the bed down. If it does so, it can be because of some extruded material left behind, which is no real problem. It can, however, be required to re-calibrate the Z-height end-stop. For more information about this, please refer to the 'Troubleshooting' info here.

Printing process

o