LEDLightDistrict

Projects
Participants	Guido, Wizzup
Skills	soldering, coding
Status	Active
Niche	Electronics
Purpose	World domination

Project to LED'ify the outside facing glass 'block' wall. each glass box will be a pixel the space

Turning it on/off

• On: Plug in its power supply
• Off: Pull out its power supply

Doesn't work!

• log in to indicio
• add yourself to the dailup group
• git checkout https://github.com/techinc/lewd.git
• follow instructions in lib/README to install USPP
• cd src ; python ledwall.py

Hardware

Design

Overview

 computer ===(serial over usb)===> arduino ===(SPI)===> ledwall
                                                           ^
                                                           | (12V)
                                                          PSU

Arduino code

#include <SPI.h>

void setup()
{
    Serial.begin(1000000);
    SPI.begin();
    SPI.setBitOrder(MSBFIRST);
    SPI.setDataMode(SPI_MODE0);
    SPI.setClockDivider(SPI_CLOCK_DIV16);
}

void loop()
{
    uint8_t c;

    for(;;)
    {
        while (!Serial.available()) {}

         /* 254 signals end of frame in the communication
          * over the serial port
          */
         if ( (c = Serial.read()) == 254 )
            delay(1); /* the WS2801 chips will latch after not getting
                       * any data for .5ms, so we wait 1ms
                       */
        else
            SPI.transfer(c); /* not end of frame? push data */
    }
}

Arduino pin-out

The code uses the hardware SPI present on the the ATMega

• Green wire on Pin 13 is Clock
• Yellow wire on Pin 11 is Data
• Black wire should be connected to the arduino's ground pin
• Red wire should NOT be connected to the arduino as it will break it!

PSU

Software Implementations

[https://github.com/techinc/lewd The current python based implementation called lewd] runs on the machine connected to the LED-Wall over a serial port.

The older javascript node.js version can communicate with the python implementation to push frames to the LED-Wall using TCP sockets.

Python documentation (temporary location) http://old.villavu.com/merlijn/lewd

Lewd

The Python (lewd) implementation features several backends. LedScreen, RemoteLedScreen and VirtualLedScreen used for local, remote and virtual access respectively.

See the file "ledwall.py" for an example on how to use all these different LedWall frontends. At the space, you should typically use RemoteLedScreen to interface with the (already running) server to the LEDWall.

To just play around with the code locally, look into the VirtualLedScreen code; you will need to install pygame to actually use the local UI.

Python documentation (temporary location)

http://old.villavu.com/merlijn/lewd

Photos & Videos

• 
• 
• 
• 
• 

OLD

Project to LED'ify the outside facing glass 'block' wall. each glass box will be a pixel

The pledge has been funded and the wall has been built

TODO:

• Finish documentation
• Host documentation somewhere
• Add nice pictures of the (new) LED wall in action.
• Set up the software in such a way that it is trivial for anyone to at least "start" the ledwall in normal operation.

Usage

Plug both power supplies at either side of the wall

The arduino is by the power supply on the left hand side. The computer powering the server is under the retro gaming table.

Running the software is pretty trivial; but requires access to the machine connected to the ledwall. Alternatively, you can attach your machine to the ledwall yourself and run the software locally.

On whatever machine that is connected to the LED wall over USB (serial); run the file net/net.py and then, in another terminal, run the file ledwall.py with the -net flag. Alternatively, you can just run the ledwall.py file with no flags, but do not run the net.py file concurrently in this case.