Difference between revisions of "LAOSLaserCutter"
(Created page with "{{Inventory |Description=Laser Cutter on loan from Daan Uttien |Category=Mechanics |Operational Status=Working |Super Users=Amx109, Narya, |Received at=2014/01/31 |Acquisitio...") |
|||
| (15 intermediate revisions by 10 users not shown) | |||
| Line 2: | Line 2: | ||
|Description=Laser Cutter on loan from Daan Uttien | |Description=Laser Cutter on loan from Daan Uttien | ||
|Category=Mechanics | |Category=Mechanics | ||
| − | |Operational Status= | + | |Operational Status=BROKEN |
| − | |Super Users= | + | |Super Users=User:sjaan, User:mattronix |
|Received at=2014/01/31 | |Received at=2014/01/31 | ||
| − | |Acquisition Details=on temporary loan | + | |Acquisition Details=on temporary loan // as Daan is not a member anymore >> STATUS? |
|Owner=Daan Uttien | |Owner=Daan Uttien | ||
}} | }} | ||
This laser cutter has been given on temporary loan to TechInc by Daan. | This laser cutter has been given on temporary loan to TechInc by Daan. | ||
| + | |||
| + | It is to be used only by those who have received training to use it. | ||
| + | |||
| + | = Description = | ||
| + | The laser cutter is a customized version of the HPC LS3020 with a 60 Watt C02 laser cutter and engraver. The electronics have been replaced with the LAOS laser electronics (link).<br> | ||
| + | |||
| + | The laser cutter is currently networked and requires the user to install and configure Visicut(link) for usage. | ||
| + | |||
| + | = Machine Maintainers = | ||
| + | |||
| + | Should anything with the machine go wrong, please turn it off and contact one of the following | ||
| + | >> NEEDS MORE MAINTAINERS / regular maintenance | ||
| + | [[User:Djuttien|Djuttien]] | ||
| + | [[User:Narya|Narya]] | ||
| + | [[User:sjaan|sjaan]] | ||
= Usage = | = Usage = | ||
| Line 16: | Line 31: | ||
Your laptop must have Visicut installed and be configured to talk to the printer, which is network enabled. | Your laptop must have Visicut installed and be configured to talk to the printer, which is network enabled. | ||
| − | = Visicut Configuration = | + | * Step 1 - switch on the machine |
| + | * Step 2 - check that the suction is switched on, and the water for the coolant is flowing | ||
| + | * Step 3 - place material on bed, secure it if necessary | ||
| + | * Step 4 - close lid, and 'execute' the print in visicut | ||
| + | * Step 5 - watch the print carefully - DO NOT leave the laser cutter unattended - fire is a big risk | ||
| + | * Step 6 - ... | ||
| + | * Step 7 - PROFIT | ||
| + | |||
| + | == Visicut Configuration == | ||
| + | |||
| + | = Settings for Cutting = | ||
| + | |||
| + | Power should never be higher than 90% | ||
| + | |||
| + | = Cost = | ||
| + | |||
| + | The agreed cost has been set to 10 EUR per hour. This covers basic costs of things that need replacing, such as mirrors, laser tube, belts etc. | ||
| + | |||
| + | = Maintenance = | ||
| + | |||
| + | Regular maintenance to be undertaken should be | ||
| + | |||
| + | * cleaning of mirrors | ||
| + | * calibration of the Z height | ||
| + | * check for damage to mirrors | ||
| + | * checking belts for tension | ||
| + | * checking calibration via known print (eg 10mm x 10mm cube) | ||
| + | |||
| + | = Pledge = | ||
| + | |||
| + | Status 2019: cathode+anode cables are loose - graphite/difficult to solder | ||
| + | |||
| + | someone fixed/bypassed it using this: | ||
| + | |||
| + | https://dzone.com/articles/replacing-a-cheap-chinese-co2-laser-tube | ||
| + | |||
| + | we should order https://nl.mouser.com/ProductDetail/571-1-5050871-9 as it worked for above user | ||
| + | |||
| + | also it should be rotated a bit so the connectors face "up" | ||
| + | |||
| + | Since the machine is broken, we've started a pledge to buy a new laser tube. This might not be the only problem, it seems there's a firmware issue that needs looking at. | ||
| + | |||
| + | People who've pledged so far: | ||
| + | |||
| + | * [[User:DrWhax]] - 25 | ||
| + | * [[User:Chotee]] - 25 | ||
| + | * [[User:sjaan]] - 25 | ||
| + | * [[User:Djuttien]] - 25 | ||
| + | * [[User:bigmacfoobar]] - 6 biertjes voor daan ;) | ||
| + | * [[User:webmind]] - 25 | ||
| + | ==Photos== | ||
| + | [[File:IMG_0965.JPG|320px|Lasercutter]] | ||
| + | [[File:IMG_0966.JPG|320px|Lasercutter]] | ||
| + | [[File:IMG_0967.JPG|320px|Lasercutter]] | ||
| + | [[File:IMG_0969.JPG|320px|Lasercutter]] | ||
Latest revision as of 11:58, 10 November 2022
| TechInc Inventory | |
|---|---|
| Description | Laser Cutter on loan from Daan Uttien |
| Category | Mechanics |
| Operational Status | BROKEN |
| Super Users | User:sjaan, User:mattronix |
| Received at | 2014/01/31 |
| Acquisition Details | on temporary loan // as Daan is not a member anymore >> STATUS? |
| Owner | Daan Uttien |
This laser cutter has been given on temporary loan to TechInc by Daan.
It is to be used only by those who have received training to use it.
Contents
Description
The laser cutter is a customized version of the HPC LS3020 with a 60 Watt C02 laser cutter and engraver. The electronics have been replaced with the LAOS laser electronics (link).
The laser cutter is currently networked and requires the user to install and configure Visicut(link) for usage.
Machine Maintainers
Should anything with the machine go wrong, please turn it off and contact one of the following >> NEEDS MORE MAINTAINERS / regular maintenance Djuttien Narya sjaan
Usage
You must have received training to use this machine.
Your laptop must have Visicut installed and be configured to talk to the printer, which is network enabled.
- Step 1 - switch on the machine
- Step 2 - check that the suction is switched on, and the water for the coolant is flowing
- Step 3 - place material on bed, secure it if necessary
- Step 4 - close lid, and 'execute' the print in visicut
- Step 5 - watch the print carefully - DO NOT leave the laser cutter unattended - fire is a big risk
- Step 6 - ...
- Step 7 - PROFIT
Visicut Configuration
Settings for Cutting
Power should never be higher than 90%
Cost
The agreed cost has been set to 10 EUR per hour. This covers basic costs of things that need replacing, such as mirrors, laser tube, belts etc.
Maintenance
Regular maintenance to be undertaken should be
- cleaning of mirrors
- calibration of the Z height
- check for damage to mirrors
- checking belts for tension
- checking calibration via known print (eg 10mm x 10mm cube)
Pledge
Status 2019: cathode+anode cables are loose - graphite/difficult to solder
someone fixed/bypassed it using this:
https://dzone.com/articles/replacing-a-cheap-chinese-co2-laser-tube
we should order https://nl.mouser.com/ProductDetail/571-1-5050871-9 as it worked for above user
also it should be rotated a bit so the connectors face "up"
Since the machine is broken, we've started a pledge to buy a new laser tube. This might not be the only problem, it seems there's a firmware issue that needs looking at.
People who've pledged so far:
- User:DrWhax - 25
- User:Chotee - 25
- User:sjaan - 25
- User:Djuttien - 25
- User:bigmacfoobar - 6 biertjes voor daan ;)
- User:webmind - 25
Photos
