Difference between revisions of "AnusCopter"
m (→Social) |
m (Stuff) |
||
| Line 47: | Line 47: | ||
LIPO charge bag | LIPO charge bag | ||
| + | ==Spare parts== | ||
| + | 5x Turnigy D2822/17 1100KV Brushless | ||
| + | |||
| + | 10x XT60 gold male and female connectors | ||
| + | |||
| + | 1 black (HJ) and 2 white (Firefly) 450 frame arms | ||
| + | |||
| + | Firefly fibreglass body parts | ||
| + | |||
| + | Some 8045 propellers | ||
| + | |||
| + | Velcro straps | ||
| + | |||
==In transit== | ==In transit== | ||
25x M3 7mm Philips head screw | 25x M3 7mm Philips head screw | ||
| + | |||
| + | 2 black 2 white HJ frame arms | ||
| + | |||
| + | Dupont wire female female | ||
| + | |||
| + | Some 8045 propellors | ||
=Build log= | =Build log= | ||
[[File:AnusFirstCrash.jpg|thumb|First crash]] | [[File:AnusFirstCrash.jpg|thumb|First crash]] | ||
Revision as of 15:25, 21 December 2013
| Projects | |
|---|---|
| |
| Participants | Ranzbak, The JinX |
| Skills | Soldering, Electronics, Coding, UI design |
| Status | Getting parts |
| Niche | Electronics |
| Purpose | Fun |
Contents
Components
HJ 450 "classic" frame
4x Turnigy D2822/17 1100KV Brushless
4x 8045 CW CCW Propellers
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC (2 with BEC)
AeroQuad 32 Flight Control board v2 (baloo)
Turnigy 9X 2.4GHz 8Ch Receiver (V2)
Turnigy 2200mAh 3S (30C+35C) LIPO
XRF wireless RF radio UART RS232
LS20031 GPS + micro JST 6 (4 wires used)
10 strand Dupont cable female-female
6 female jumper leads
4x 470 Ohm resistor and 2 white 5mm LED 2 red LED 5mm
1x XT60 and 8x 3.5mm gold bullet connectors
Heat shrink tubes
Velcro tape <3
Accessoires
Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO + FS-TH9X-B-Module
XBee Explorer Dongle + XRF wireless RF radio UART RS232 + SMA connector + Quad-band Cellular Antenna SMA
Case for XRF dongle http://www.thingiverse.com/thing:204516
Turnigy Accucel-6 50W 6A Balancer/Charger
LIPO charge bag
Spare parts
5x Turnigy D2822/17 1100KV Brushless
10x XT60 gold male and female connectors
1 black (HJ) and 2 white (Firefly) 450 frame arms
Firefly fibreglass body parts
Some 8045 propellers
Velcro straps
In transit
25x M3 7mm Philips head screw
2 black 2 white HJ frame arms
Dupont wire female female
Some 8045 propellors
Build log
- 2013-11-20 put AeroQuad in case
- 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm)
- 2013-11-26 charged batteries, added receiver and battery strap
- 2013-11-27 battery monitor leads (and header for LEDs) added
- 2013-12-04 XT60 to power board soldered
- 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS
- 2013-12-11 added 4 pin micro JST to XRF module and 2 front and 2 rear LEDs
- 2013-12-15 inserted TX installed props created case for XRF
- 2013-12-21 new rear end frame
Flight log
- 2013-12-15 maiden flight .. second flight went too high, crashed and broke frame
ToDo
Landing gear http://www.thingiverse.com/thing:60722
T B A
Outer shell
Ultrasonic Range Finder (LV EZ-0)
Camera's and FPV transmitter / receiver
