Difference between revisions of "AnusCopter"
m (→Build log) |
(Added projects) |
||
| Line 74: | Line 74: | ||
=Links= | =Links= | ||
| + | ==Other local flying projects== | ||
[[Justa copter 1]] | [[Justa copter 1]] | ||
| + | |||
| + | [[Phicoh_Copter_1]] | ||
| + | |||
| + | [[NarCopter]] | ||
| + | |||
| + | [[Yiodah copter]] | ||
| + | |||
| + | [[DiscoDrone]] | ||
| + | |||
| + | [[QuadcopterAmraam]] | ||
| + | |||
| + | ==Social== | ||
| + | |||
| + | [Quadcopter workshop[]] | ||
| + | |||
| + | ==Useful== | ||
[http://git.etv.cx/?a=tree&p=stm32-flightcontrol STM32 flightcontroll] | [http://git.etv.cx/?a=tree&p=stm32-flightcontrol STM32 flightcontroll] | ||
[http://aeroquad.com/ Aero Quad] | [http://aeroquad.com/ Aero Quad] | ||
Revision as of 14:57, 21 December 2013
| Projects | |
|---|---|
| |
| Participants | Ranzbak, The JinX |
| Skills | Soldering, Electronics, Coding, UI design |
| Status | Getting parts |
| Niche | Electronics |
| Purpose | Fun |
Contents
Components
HJ 450 "classic" frame
4x Turnigy D2822/17 1100KV Brushless
4x 8045 CW CCW Propellers
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC (2 with BEC)
AeroQuad 32 Flight Control board v2 (baloo)
Turnigy 9X 2.4GHz 8Ch Receiver (V2)
Turnigy 2200mAh 3S (30C+35C) LIPO
XRF wireless RF radio UART RS232
LS20031 GPS + micro JST 6 (4 wires used)
10 strand Dupont cable female-female
6 female jumper leads
4x 470 Ohm resistor and 2 white 5mm LED 2 red LED 5mm
1x XT60 and 8x 3.5mm gold bullet connectors
Heat shrink tubes
Velcro tape <3
Accessoires
Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO + FS-TH9X-B-Module
XBee Explorer Dongle + XRF wireless RF radio UART RS232 + SMA connector + Quad-band Cellular Antenna SMA
Case for XRF dongle http://www.thingiverse.com/thing:204516
Turnigy Accucel-6 50W 6A Balancer/Charger
LIPO charge bag
In transit
25x M3 7mm Philips head screw
Build log
- 2013-11-20 put AeroQuad in case
- 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm)
- 2013-11-26 charged batteries, added receiver and battery strap
- 2013-11-27 battery monitor leads (and header for LEDs) added
- 2013-12-04 XT60 to power board soldered
- 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS
- 2013-12-11 added 4 pin micro JST to XRF module and 2 front and 2 rear LEDs
- 2013-12-15 inserted TX installed props created case for XRF
- 2013-12-21 new rear end frame
Flight log
- 2013-12-15 maiden flight .. second flight went too high, crashed and broke frame
ToDo
Landing gear http://www.thingiverse.com/thing:60722
T B A
Outer shell
Ultrasonic Range Finder (LV EZ-0)
Camera's and FPV transmitter / receiver
Links
Other local flying projects
Social
[Quadcopter workshop[]]
