Difference between revisions of "AnusCopter"
(→Components) |
|||
| Line 32: | Line 32: | ||
1x XT60 and 8x 3.5mm gold bullet connectors | 1x XT60 and 8x 3.5mm gold bullet connectors | ||
| + | |||
| + | Heat shrink tubes | ||
Velcro tape <3 | Velcro tape <3 | ||
==Accessoires== | ==Accessoires== | ||
| − | Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO | + | Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO + FS-TH9X-B-Module |
| − | XRF wireless RF radio UART RS232 | + | XBee Explorer Dongle + XRF wireless RF radio UART RS232 + SMA connector + Quad-band Cellular Antenna SMA |
Turnigy Accucel-6 50W 6A Balancer/Charger | Turnigy Accucel-6 50W 6A Balancer/Charger | ||
| Line 44: | Line 46: | ||
LIPO charge bag | LIPO charge bag | ||
==In transit== | ==In transit== | ||
| − | |||
| − | |||
Some 8045 CW CCW Propellers | Some 8045 CW CCW Propellers | ||
| Line 51: | Line 51: | ||
25x M3 7mm Philips head screw | 25x M3 7mm Philips head screw | ||
| − | |||
| − | |||
| − | |||
=Build log= | =Build log= | ||
| − | |||
* 2013-11-20 put AeroQuad in case | * 2013-11-20 put AeroQuad in case | ||
* 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm) | * 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm) | ||
| Line 63: | Line 59: | ||
* 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS | * 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS | ||
* 2013-12-11 added 4 pin micro JST to XRF module and 2 front and 2 rear LEDs | * 2013-12-11 added 4 pin micro JST to XRF module and 2 front and 2 rear LEDs | ||
| − | + | * 2013-12-15 fixed TX installed props | |
| + | =Flight log= | ||
| + | * 2013-12-15 maiden flight .. second flight went too high, crashed and broke frame | ||
=ToDo= | =ToDo= | ||
Landing gear | Landing gear | ||
| − | |||
==T B A== | ==T B A== | ||
Outer shell | Outer shell | ||
Revision as of 15:58, 15 December 2013
| Projects | |
|---|---|
| |
| Participants | Ranzbak, The JinX |
| Skills | Soldering, Electronics, Coding, UI design |
| Status | Getting parts |
| Niche | Electronics |
| Purpose | Fun |
Contents
Components
HJ 450 "classic" frame
4x Turnigy D2822/17 1100KV Brushless
4x 8045 CW CCW Propellers
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC (2 with BEC)
AeroQuad 32 Flight Control board v2 (baloo)
Turnigy 9X 2.4GHz 8Ch Receiver (V2)
Turnigy 2200mAh 3S (30C+35C) LIPO
XRF wireless RF radio UART RS232
LS20031 GPS + micro JST 6 (4 wires used)
10 strand Dupont cable female-female
6 female jumper leads
4x 470 Ohm resistor and 2 white 5mm LED 2 red LED 5mm
1x XT60 and 8x 3.5mm gold bullet connectors
Heat shrink tubes
Velcro tape <3
Accessoires
Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO + FS-TH9X-B-Module
XBee Explorer Dongle + XRF wireless RF radio UART RS232 + SMA connector + Quad-band Cellular Antenna SMA
Turnigy Accucel-6 50W 6A Balancer/Charger
LIPO charge bag
In transit
Some 8045 CW CCW Propellers
10x Male+Female XT60 connector
25x M3 7mm Philips head screw
Build log
- 2013-11-20 put AeroQuad in case
- 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm)
- 2013-11-26 charged batteries, added receiver and battery strap
- 2013-11-27 battery monitor leads (and header for LEDs) added
- 2013-12-04 XT60 to power board soldered
- 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS
- 2013-12-11 added 4 pin micro JST to XRF module and 2 front and 2 rear LEDs
- 2013-12-15 fixed TX installed props
Flight log
- 2013-12-15 maiden flight .. second flight went too high, crashed and broke frame
ToDo
Landing gear
T B A
Outer shell
Ultrasonic Range Finder (LV EZ-0)
Camera's and FPV transmitter / receiver
