Difference between revisions of "AnusCopter"
m (→Accessoires) |
m |
||
| Line 15: | Line 15: | ||
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC | 4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC | ||
| − | AeroQuad 32 Flight Control board v2 | + | AeroQuad 32 Flight Control board v2 (baloo) |
Turnigy 9X 2.4GHz 8Ch Receiver (V2) | Turnigy 9X 2.4GHz 8Ch Receiver (V2) | ||
| − | + | Turnigy 2200mAh 3S (30C+35C) LIPO | |
| − | XRF wireless RF radio UART RS232 | + | XRF wireless RF radio UART RS232 |
| − | LS20031 GPS | + | LS20031 GPS + micro JST 6 (4 wires used) |
| − | 10 strand | + | 10 strand Dupont cable female-female |
| − | 6 female jumper leads | + | 6 female jumper leads |
Velcro tape <3 | Velcro tape <3 | ||
| − | XT60 and 3.5mm gold bullet connectors | + | 1x XT60 and 8x 3.5mm gold bullet connectors |
==Accessoires== | ==Accessoires== | ||
Revision as of 02:26, 8 December 2013
| Projects | |
|---|---|
| |
| Participants | Ranzbak, The JinX |
| Skills | Soldering, Electronics, Coding, UI design |
| Status | Getting parts |
| Niche | Electronics |
| Purpose | Fun |
Components
HJ 450 "classic" frame
4x Turnigy D2822/17 1100KV Brushless
4x 8045 CW CCW Propellers
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC
AeroQuad 32 Flight Control board v2 (baloo)
Turnigy 9X 2.4GHz 8Ch Receiver (V2)
Turnigy 2200mAh 3S (30C+35C) LIPO
XRF wireless RF radio UART RS232
LS20031 GPS + micro JST 6 (4 wires used)
10 strand Dupont cable female-female
6 female jumper leads
Velcro tape <3
1x XT60 and 8x 3.5mm gold bullet connectors
Accessoires
Turnigy 9XR Transmitter Mode 2 + 11.1v (3s) 2200mAh 1.5C LIPO
XRF wireless RF radio UART RS232
Turnigy Accucel-6 50W 6A Balancer/Charger
In transit
4x Turnigy Multistar 30 Amp Multi-rotor Brushless ESC
FS-TH9X-B-Module
Some 8045 CW CCW Propellers
10x Male+Female XT60 connector
25x M3 7mm Philips head screw
XBee Explorer Dongle + Quad-band Cellular Antenna SMA + SMA connector for XRF
Build log
- 2013-11-20 put AeroQuad in case
- 2013-11-23 assembled body, screwed motors on with 16x M3 (~6mm)
- 2013-11-26 charged batteries, added receiver and battery strap
- 2013-11-27 battery monitor leads (and header for LEDs) added
- 2013-12-04 XT60 to power board soldered
- 2013-12-07 8x 3.5mm gold bullet connectors, installed ESCs, 6 pin micro JST to GPS
ToDo
Serial uplink (telemetry)
LEDs
Wait for TX :-(
T B A
Landing gear
Ultrasonic Range Finder (LV EZ-0)
Camera's and FPV transmitter / receiver
